Design and Implementation of a Digital Control System for Lead Acid Battery Charging

Marie Danielle Fendji; Franck Mbah Kimbong; Ioannis Tsipouridis; Pierre Tsafack

doi:doi:10.11648/j.jeee.20231101.13

| Peer-Reviewed

Design and Implementation of a Digital Control System for Lead Acid Battery Charging

Marie Danielle Fendji, Franck Mbah Kimbong, Ioannis Tsipouridis, Pierre Tsafack

Published in Journal of Electrical and Electronic Engineering (Volume 11, Issue 1)

Received: 10 January 2023 Accepted: 1 February 2023 Published: 14 February 2023

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Ensuring a long battery life and satisfactory performance requires accurate charging cycles. There are three phases to the charge cycle - Constant Current Charge, Constant Voltage Charge, and Float Charge. It is usual that lead acid battery users complain about fast degrading performance because most the low cost commercially available lead Acid Battery chargers provides only single-stage charging phase which is that of constant-voltage charging phase. To ensure long service life and good performance, it is of paramount importance that all charging modes are respected. This said it is clear that the battery charger should have a certain degree of controllability over voltage and current quantities through-out the charging process. In this paper, we designed and built a lead acid battery charger to use in conjunction with a synchronous buck converter topology. After implementing and testing the system, we obtained good results in both the quantitative and qualitative analysis of the implemented system tested, a 12 V- 7000mAh battery. With the help of a MCU-based digital control system containing two different control transfer functions - constant current Feedback Control and Constant Voltage Feedback Control monitoring the charging process proved possible without any overshoot. The prototype showed us an efficiency rating of 86.60%, the maximum error level was recorded at 0.05V, and there were no problems related to overshoot or transient response when testing our prototype which worked flawlessly.

Published in	Journal of Electrical and Electronic Engineering (Volume 11, Issue 1)
DOI	10.11648/j.jeee.20231101.13
Page(s)	23-33
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2023. Published by Science Publishing Group

Keywords

Lead Acid Battery, Battery Charging, Buck Converter, Control System

References

[1]	Pachauri, R. K., & Mayer, L. (2014). Intergovernmental Panel on Climate Change, Climate Change 2014, Synthesis Report. IPCC: Geneva, Switzerland.
[2]	Liddle, B., & Sadorsky, P. (2017). How much does increasing non-fossil fuels in electricity generation reduce carbon dioxide emissions? Applied Energy, 197, 212-221.
[3]	Lalouni, S., Rekioua, D., Rekioua, T., & Matagne, E. (2009). Fuzzy logic control of stand-alone photovoltaic system with battery storage. Journal of power Sources, 193 (2), 899-907.
[4]	Hirech, K., Melhaoui, M., Yaden, F., Baghaz, E., & Kassmi, K. (2013). Design and realization of an autonomous system equipped with a charge/discharge regulator and digital MPPT command. Energy Procedia, 42, 503-512.
[5]	López, J., Seleme Jr, S. I., Donoso, P. F., Morais, L. M. F., Cortizo, P. C., & Severo, M. A. (2016). Digital control strategy for a buck converter operating as a battery charger for stand-alone photovoltaic systems. Solar Energy, 140, 171-187.
[6]	David, B. M., & Sreeja, K. K. (2015). A Review of sliding mode control of DC-DC converters. International Research Journal of Engineering and Technology, 2 (4), 1382-1386.
[7]	Kousksou, T., Bruel, P., Jamil, A., El Rhafiki, T., & Zeraouli, Y. (2014). Energy storage: Applications and challenges. Solar Energy Materials and Solar Cells, 120, 59-80.
[8]	Kaldellis, J. K., Zafirakis, D., & Kavadias, K. (2009). Techno-economic comparison of energy storage systems for island autonomous electrical networks. Renewable and Sustainable Energy Reviews, 13 (2), 378-392.
[9]	Evans, A., Strezov, V., & Evans, T. J. (2012). Assessment of utility energy storage options for increased renewable energy penetration. Renewable and Sustainable Energy Reviews, 16 (6), 4141-4147.
[10]	Hoppmann, J., Volland, J., Schmidt, T. S., & Hoffmann, V. H. (2014). The economic viability of battery storage for residential solar photovoltaic systems–A review and a simulation model. Renewable and Sustainable Energy Reviews, 39, 1101-1118.
[11]	Hesse, H. C., Martins, R., Musilek, P., Naumann, M., Truong, C. N., & Jossen, A. (2017). Economic optimization of component sizing for residential battery storage systems. Energies, 10 (7), 835.
[12]	Erickson, R. W., & Maksimovic, D. (2007). Fundamentals of power electronics. Springer Science & Business Media.
[13]	Utkin, V. I. (1992). Scope of the theory of sliding modes. In Sliding modes in control and optimization (pp. 1-11). Springer, Berlin, Heidelberg.
[14]	Hua, A. C. C., & Syue, B. Z. W. (2010, June). Charge and discharge characteristics of lead-acid battery and LiFePO₄ battery. In The 2010 International Power Electronics Conference-ECCE ASIA- (pp. 1478-1483). IEEE.
[15]	Lee, C. S., Lin, H. C., & Lai, S. Y. (2013). Development of fast large lead-acid battery charging system using multi-state strategy. International Journal on Computer, Consumer and Control (IJ3C), 2 (2), 56-65.
[16]	Hua, C. C., & Lin, M. Y. (2000, December). A study of charging control of lead-acid battery for electric vehicles. In ISIE'2000. Proceedings of the 2000 IEEE International Symposium on Industrial Electronics (Cat. No. 00TH8543) (Vol. 1, pp. 135-140). IEEE.
[17]	Banguero, E., Correcher, A., Pérez-Navarro, Á., Morant, F., & Aristizabal, A. (2018). A review on battery charging and discharging control strategies: Application to renewable energy systems. Energies, 11 (4), 1021.
[18]	Cuoghi, S., Ntogramatzidis, L., Padula, F., & Grandi, G. (2018). Direct digital design of PIDF controllers with ComPlex zeros for DC-DC buck converters. Energies, 12 (1), 36.
[19]	Mahmoud, M. M. (2004). On the storage batteries used in solar electric power systems and development of an algorithm for determining their ampere–hour capacity. Electric Power Systems Research, 71 (1), 85-89.
[20]	Louie, H., & Louie, H. (2018). Design and implementation of off-grid systems. Off-Grid Electrical Systems in Developing Countries, 387-445.

Cite This Article

Plain Text BibTeX RIS

APA Style

Marie Danielle Fendji, Franck Mbah Kimbong, Ioannis Tsipouridis, Pierre Tsafack. (2023). Design and Implementation of a Digital Control System for Lead Acid Battery Charging. Journal of Electrical and Electronic Engineering, 11(1), 23-33. https://doi.org/10.11648/j.jeee.20231101.13

Copy | Download

ACS Style

Marie Danielle Fendji; Franck Mbah Kimbong; Ioannis Tsipouridis; Pierre Tsafack. Design and Implementation of a Digital Control System for Lead Acid Battery Charging. J. Electr. Electron. Eng. 2023, 11(1), 23-33. doi: 10.11648/j.jeee.20231101.13

Copy | Download

AMA Style

Marie Danielle Fendji, Franck Mbah Kimbong, Ioannis Tsipouridis, Pierre Tsafack. Design and Implementation of a Digital Control System for Lead Acid Battery Charging. J Electr Electron Eng. 2023;11(1):23-33. doi: 10.11648/j.jeee.20231101.13

Copy | Download

@article{10.11648/j.jeee.20231101.13,
  author = {Marie Danielle Fendji and Franck Mbah Kimbong and Ioannis Tsipouridis and Pierre Tsafack},
  title = {Design and Implementation of a Digital Control System for Lead Acid Battery Charging},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {11},
  number = {1},
  pages = {23-33},
  doi = {10.11648/j.jeee.20231101.13},
  url = {https://doi.org/10.11648/j.jeee.20231101.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20231101.13},
  abstract = {Ensuring a long battery life and satisfactory performance requires accurate charging cycles. There are three phases to the charge cycle - Constant Current Charge, Constant Voltage Charge, and Float Charge. It is usual that lead acid battery users complain about fast degrading performance because most the low cost commercially available lead Acid Battery chargers provides only single-stage charging phase which is that of constant-voltage charging phase. To ensure long service life and good performance, it is of paramount importance that all charging modes are respected. This said it is clear that the battery charger should have a certain degree of controllability over voltage and current quantities through-out the charging process. In this paper, we designed and built a lead acid battery charger to use in conjunction with a synchronous buck converter topology. After implementing and testing the system, we obtained good results in both the quantitative and qualitative analysis of the implemented system tested, a 12 V- 7000mAh battery. With the help of a MCU-based digital control system containing two different control transfer functions - constant current Feedback Control and Constant Voltage Feedback Control monitoring the charging process proved possible without any overshoot. The prototype showed us an efficiency rating of 86.60%, the maximum error level was recorded at 0.05V, and there were no problems related to overshoot or transient response when testing our prototype which worked flawlessly.},
 year = {2023}
}

Copy | Download

TY  - JOUR
T1  - Design and Implementation of a Digital Control System for Lead Acid Battery Charging
AU  - Marie Danielle Fendji
AU  - Franck Mbah Kimbong
AU  - Ioannis Tsipouridis
AU  - Pierre Tsafack
Y1  - 2023/02/14
PY  - 2023
N1  - https://doi.org/10.11648/j.jeee.20231101.13
DO  - 10.11648/j.jeee.20231101.13
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 23
EP  - 33
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20231101.13
AB  - Ensuring a long battery life and satisfactory performance requires accurate charging cycles. There are three phases to the charge cycle - Constant Current Charge, Constant Voltage Charge, and Float Charge. It is usual that lead acid battery users complain about fast degrading performance because most the low cost commercially available lead Acid Battery chargers provides only single-stage charging phase which is that of constant-voltage charging phase. To ensure long service life and good performance, it is of paramount importance that all charging modes are respected. This said it is clear that the battery charger should have a certain degree of controllability over voltage and current quantities through-out the charging process. In this paper, we designed and built a lead acid battery charger to use in conjunction with a synchronous buck converter topology. After implementing and testing the system, we obtained good results in both the quantitative and qualitative analysis of the implemented system tested, a 12 V- 7000mAh battery. With the help of a MCU-based digital control system containing two different control transfer functions - constant current Feedback Control and Constant Voltage Feedback Control monitoring the charging process proved possible without any overshoot. The prototype showed us an efficiency rating of 86.60%, the maximum error level was recorded at 0.05V, and there were no problems related to overshoot or transient response when testing our prototype which worked flawlessly.
VL  - 11
IS  - 1
ER  -

Copy | Download

Author Information

Marie Danielle Fendji

Electrical and Electronic Engineering, Faculty of Engineering and Technology, University of Buea, Buea, Cameroon
Franck Mbah Kimbong

Electrical and Electronic Engineering, Faculty of Engineering and Technology, University of Buea, Buea, Cameroon
Ioannis Tsipouridis

Renewable Energy and Climate Change Research Center-RECCReC, Institute/Technical University of Mombasa, Mombasa, Kenya
Pierre Tsafack

Electrical and Electronic Engineering, Faculty of Engineering and Technology, University of Buea, Buea, Cameroon

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Marie Danielle Fendji, Franck Mbah Kimbong, Ioannis Tsipouridis, Pierre Tsafack. (2023). Design and Implementation of a Digital Control System for Lead Acid Battery Charging. Journal of Electrical and Electronic Engineering, 11(1), 23-33. https://doi.org/10.11648/j.jeee.20231101.13

Copy | Download

ACS Style

Marie Danielle Fendji; Franck Mbah Kimbong; Ioannis Tsipouridis; Pierre Tsafack. Design and Implementation of a Digital Control System for Lead Acid Battery Charging. J. Electr. Electron. Eng. 2023, 11(1), 23-33. doi: 10.11648/j.jeee.20231101.13

Copy | Download

AMA Style

Marie Danielle Fendji, Franck Mbah Kimbong, Ioannis Tsipouridis, Pierre Tsafack. Design and Implementation of a Digital Control System for Lead Acid Battery Charging. J Electr Electron Eng. 2023;11(1):23-33. doi: 10.11648/j.jeee.20231101.13

Copy | Download

@article{10.11648/j.jeee.20231101.13,
  author = {Marie Danielle Fendji and Franck Mbah Kimbong and Ioannis Tsipouridis and Pierre Tsafack},
  title = {Design and Implementation of a Digital Control System for Lead Acid Battery Charging},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {11},
  number = {1},
  pages = {23-33},
  doi = {10.11648/j.jeee.20231101.13},
  url = {https://doi.org/10.11648/j.jeee.20231101.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20231101.13},
  abstract = {Ensuring a long battery life and satisfactory performance requires accurate charging cycles. There are three phases to the charge cycle - Constant Current Charge, Constant Voltage Charge, and Float Charge. It is usual that lead acid battery users complain about fast degrading performance because most the low cost commercially available lead Acid Battery chargers provides only single-stage charging phase which is that of constant-voltage charging phase. To ensure long service life and good performance, it is of paramount importance that all charging modes are respected. This said it is clear that the battery charger should have a certain degree of controllability over voltage and current quantities through-out the charging process. In this paper, we designed and built a lead acid battery charger to use in conjunction with a synchronous buck converter topology. After implementing and testing the system, we obtained good results in both the quantitative and qualitative analysis of the implemented system tested, a 12 V- 7000mAh battery. With the help of a MCU-based digital control system containing two different control transfer functions - constant current Feedback Control and Constant Voltage Feedback Control monitoring the charging process proved possible without any overshoot. The prototype showed us an efficiency rating of 86.60%, the maximum error level was recorded at 0.05V, and there were no problems related to overshoot or transient response when testing our prototype which worked flawlessly.},
 year = {2023}
}

Copy | Download

TY  - JOUR
T1  - Design and Implementation of a Digital Control System for Lead Acid Battery Charging
AU  - Marie Danielle Fendji
AU  - Franck Mbah Kimbong
AU  - Ioannis Tsipouridis
AU  - Pierre Tsafack
Y1  - 2023/02/14
PY  - 2023
N1  - https://doi.org/10.11648/j.jeee.20231101.13
DO  - 10.11648/j.jeee.20231101.13
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 23
EP  - 33
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20231101.13
AB  - Ensuring a long battery life and satisfactory performance requires accurate charging cycles. There are three phases to the charge cycle - Constant Current Charge, Constant Voltage Charge, and Float Charge. It is usual that lead acid battery users complain about fast degrading performance because most the low cost commercially available lead Acid Battery chargers provides only single-stage charging phase which is that of constant-voltage charging phase. To ensure long service life and good performance, it is of paramount importance that all charging modes are respected. This said it is clear that the battery charger should have a certain degree of controllability over voltage and current quantities through-out the charging process. In this paper, we designed and built a lead acid battery charger to use in conjunction with a synchronous buck converter topology. After implementing and testing the system, we obtained good results in both the quantitative and qualitative analysis of the implemented system tested, a 12 V- 7000mAh battery. With the help of a MCU-based digital control system containing two different control transfer functions - constant current Feedback Control and Constant Voltage Feedback Control monitoring the charging process proved possible without any overshoot. The prototype showed us an efficiency rating of 86.60%, the maximum error level was recorded at 0.05V, and there were no problems related to overshoot or transient response when testing our prototype which worked flawlessly.
VL  - 11
IS  - 1
ER  -

Copy | Download