Considerations on the Use of Lumina-Porous® Biomaterial in Maxillary Sinus Floor
Douglas Rangel Goulart,
Luciana Asprino,
Márcio de Moraes,
Claudio Ferreira Nóia
Issue:
Volume 3, Issue 1, February 2015
Pages:
1-4
Received:
30 January 2015
Accepted:
13 February 2015
Published:
25 February 2015
Abstract: Maxillary sinus floor augmentation procedure, aka sinus floor lift surgery, stand out within the universe of bone reconstruction given that the maxillary sinus is a closed cavity with favorable nutrition, which enables the use of biomaterials alone. Therefore, this study aimed to report and discuss the technical and biological peculiarities of Lumina-Porous® biomaterial alone in the maxillary sinus by describing a sinus lift case which presented with little remaining bone. After the graft incorporation period two implants were installed in the grafted area to provide proper patient rehabilitation.
Abstract: Maxillary sinus floor augmentation procedure, aka sinus floor lift surgery, stand out within the universe of bone reconstruction given that the maxillary sinus is a closed cavity with favorable nutrition, which enables the use of biomaterials alone. Therefore, this study aimed to report and discuss the technical and biological peculiarities of Lumi...
Show More
Investigation of Fatigue and Compression Strength for the PMMA Reinforced by Different System for Denture Applications
Sihama Issa Salih,
Jawad Kadhum Oleiwi,
Qahtan Adnan Hamad
Issue:
Volume 3, Issue 1, February 2015
Pages:
5-13
Received:
19 January 2015
Accepted:
1 February 2015
Published:
2 March 2015
Abstract: In the present search, attempts are made to develop the properties of PMMA resin that used for upper and lower prosthesis complete denture, by addition two different types of particles, which included: nano-hydroxyapatite (nHA) particles and micro-zirconia (ZrO2) particles that added with different volume fractions of (1%, 2% and 3%) to poly methyl methacrylate (PMMA) cold cured resin as new fluid resin as a matrix. Also woven glass fiber kind (E-glass) and woven Kevlar fiber kind (49), it were added with a fixed volume fraction of (5%) to PMMA composites. In this work the composite prosthetic dentures specimens preparation was done by using (Hand Lay-Up) method as six groups which includes: the first group consists of PMMA resin reinforced by nHA particles, the second group consists of PMMA resin reinforced by ZrO2 particles, the third group consists of (PMMA-nHA) and glass fiber layer as laminated composite , the fourth group consists of (PMMA-ZrO2) and glass fiber layer, the fifth group consists of (PMMA-nHA) and Kevlar fiber layer and the sixth group consists of (PMMA-ZrO2) and Kevlar fiber layer. The compression test result shows that the values of compression strength increased with increasing the volume fraction of (nHA and ZrO2) particles for all groups’ specimens. And the results showed the (PMMA-ZrO2) composite has greater values for compression strength. As well as the results shows that the maximum value of compression strength for hybrid laminated composite is obtained in hybrid laminated composite materials for fourth groups’ specimens (PMMA-ZrO2-5% Glass Fiber). Whereas the values of fatigue strength of hybrid laminated composite (PMMA-5% Kevlar fiber-3% nHA), it was higher than the fatigue strength of hybrid laminated composite (PMMA-5% Glass fiber-3% nHA) and the base material (Pure PMMA). The fatigue strength values at (106) loading Cycle for these specimens were (52, 38 and 15 MPa) respectively.
Abstract: In the present search, attempts are made to develop the properties of PMMA resin that used for upper and lower prosthesis complete denture, by addition two different types of particles, which included: nano-hydroxyapatite (nHA) particles and micro-zirconia (ZrO2) particles that added with different volume fractions of (1%, 2% and 3%) to poly methyl...
Show More
